Advanced Automotive Fault Diagnosis

Author : Tom Denton
Publisher : Routledge
ISBN 13 : 1136430830
Total Pages : 289 pages
Book Rating : 4.31/5 ( download)

DOWNLOAD NOW!

Download or read book Advanced Automotive Fault Diagnosis written by Tom Denton and published by Routledge. This book was released on 2006-08-14 with total page 289 pages. Available in PDF, EPUB and Kindle. Book excerpt: Diagnostics, or fault finding, is a fundamental part of an automotive technician's work, and as automotive systems become increasingly complex there is a greater need for good diagnostic skills. Advanced Automotive Fault Diagnosis is the only book to treat automotive diagnostics as a science rather than a check-list procedure. Each chapter includes basic principles and examples of a vehicle system followed by the appropriate diagnostic techniques, complete with useful diagrams, flow charts, case studies and self-assessment questions. The book will help new students develop diagnostic skills and help experienced technicians improve even further. This new edition is fully updated to the latest technological developments. Two new chapters have been added – On-board diagnostics and Oscilloscope diagnostics – and the coverage has been matched to the latest curricula of motor vehicle qualifications, including: IMI and C&G Technical Certificates and NVQs; Level 4 diagnostic units; BTEC National and Higher National qualifications from Edexcel; International Motor Vehicle qualifications such as C&G 3905; and ASE certification in the USA.

Author : Tom Denton
Publisher : Routledge
ISBN 13 : 0080969550
Total Pages : 453 pages
Book Rating : 4.58/5 ( download)

DOWNLOAD NOW!

Download or read book Advanced Automotive Fault Diagnosis written by Tom Denton and published by Routledge. This book was released on 2012 with total page 453 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Automotive Fault Diagnosis covers the fundamentals of vehicle systems and components and explains the latest diagnostic techniques employed in effective vehicle maintenance and repair.

Author : Rolf Isermann
Publisher : Springer Science & Business Media
ISBN 13 : 3540303685
Total Pages : 475 pages
Book Rating : 4.88/5 ( download)

DOWNLOAD NOW!

Download or read book Fault-Diagnosis Systems written by Rolf Isermann and published by Springer Science & Business Media. This book was released on 2006-01-16 with total page 475 pages. Available in PDF, EPUB and Kindle. Book excerpt: With increasing demands for efficiency and product quality plus progress in the integration of automatic control systems in high-cost mechatronic and safety-critical processes, the field of supervision (or monitoring), fault detection and fault diagnosis plays an important role. The book gives an introduction into advanced methods of fault detection and diagnosis (FDD). After definitions of important terms, it considers the reliability, availability, safety and systems integrity of technical processes. Then fault-detection methods for single signals without models such as limit and trend checking and with harmonic and stochastic models, such as Fourier analysis, correlation and wavelets are treated. This is followed by fault detection with process models using the relationships between signals such as parameter estimation, parity equations, observers and principal component analysis. The treated fault-diagnosis methods include classification methods from Bayes classification to neural networks with decision trees and inference methods from approximate reasoning with fuzzy logic to hybrid fuzzy-neuro systems. Several practical examples for fault detection and diagnosis of DC motor drives, a centrifugal pump, automotive suspension and tire demonstrate applications.

Author : Tracy Martin
Publisher : Motorbooks
ISBN 13 : 1627886486
Total Pages : 203 pages
Book Rating : 4.82/5 ( download)

DOWNLOAD NOW!

Download or read book How To Use Automotive Diagnostic Scanners written by Tracy Martin and published by Motorbooks. This book was released on 2015-08-01 with total page 203 pages. Available in PDF, EPUB and Kindle. Book excerpt: From hand-held, dedicated units to software that turns PCs and Palm Pilots into powerful diagnostic scanners, auto enthusiasts today have a variety of methods available to make use of on-board diagnostic systems. And not only can they be used to diagnose operational faults, they can be used as low-budget data acquistion systems and dynamometers, so you can maximize your vehicle's performance. Beginning with why scanners are needed to work effectively on modern cars, this book teaches you how to choose the right scanner for your application, how to use the tool, and what each code means. "How To Use Automotive Diagnostic Scanners" is illustrated with photos and diagrams to help you understand OBD-I and OBD-II systems (including CAN) and the scanners that read the information they record. Also included is a comprehensive list of codes and what they mean. From catalytic converters and O2 sensors to emissions and automotive detective work, this is the complete reference for keeping your vehicle EPA-compliant and on the road!

Author : Steven X. Ding
Publisher : Springer Nature
ISBN 13 : 3662620049
Total Pages : 664 pages
Book Rating : 4.45/5 ( download)

DOWNLOAD NOW!

Download or read book Advanced methods for fault diagnosis and fault-tolerant control written by Steven X. Ding and published by Springer Nature. This book was released on 2020-11-24 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt: The major objective of this book is to introduce advanced design and (online) optimization methods for fault diagnosis and fault-tolerant control from different aspects. Under the aspect of system types, fault diagnosis and fault-tolerant issues are dealt with for linear time-invariant and time-varying systems as well as for nonlinear and distributed (including networked) systems. From the methodological point of view, both model-based and data-driven schemes are investigated.To allow for a self-contained study and enable an easy implementation in real applications, the necessary knowledge as well as tools in mathematics and control theory are included in this book. The main results with the fault diagnosis and fault-tolerant schemes are presented in form of algorithms and demonstrated by means of benchmark case studies. The intended audience of this book are process and control engineers, engineering students and researchers with control engineering background.

Author : Mandy Concepcion
Publisher : Mandy Concepcion
ISBN 13 :
Total Pages : 59 pages
Book Rating : 4./5 ( download)

DOWNLOAD NOW!

Download or read book Automotive Scan Tool PID Diagnostics written by Mandy Concepcion and published by Mandy Concepcion. This book was released on 2011-10-06 with total page 59 pages. Available in PDF, EPUB and Kindle. Book excerpt: Automotive Scan Tool PID Diagnostics (Diagnostics Strategies of Modern Automotive Systems ) By Mandy Concepcion In this section, the different techniques of scan tool parameter (PID) analysis will be exposed. Techniques involving PID analysis are quickly catching on, due to their speed and accuracy. By properly analyzing the different scanner PIDs, the technician can arrive at the source of the problem much faster and accurately. These procedures give rise to the new term “driver seat diagnostics”, since most of the preliminary diagnostic work is done through the scanner. However, these techniques will in no way replace the final manual tests that are a part of every diagnostic path. They are simply geared to point the technician in the right direction. Table of Contents INTRODUCTION (Introduction to scan tool diagnostics and the relevance of using PIDs or scanner parameter to perform the first leg of all diagnostics.) - Theory of Operation Behind the Different PIDs (Describes CARB, the difference between generic and enhanced PIDs, the FTP) - OBD II Generic PIDs (PID calculated and actual values, calculated data relationships, base injection timing, ECM value substitution) - OBD I & II General PID analysis (erasing code-or not, recording, analyzing and pinpoint tests, separating PIDs into groups) - Fuel Delivery Fault Detection (fuel delivery issues, intake air temp. sensor, BARO sensor, Engine LOAD, RPM PID, Short-Term Fuel Trims, Long-Term Fuel Trims, 60% of check engine light issues, block learn/integrators, Example 1: injector fault, Example 2: intake gasket issues, fuel status, ignition timing, MAP/MAF, TPS, O2 sensor, IAC, Closed Throttle, injector pulse width, voltage power, injector dutycycle, fuel trim cell) - Test #1 (Determining an engine’s fuel Consumption (rich-lean operation, duty-cycle to fuel trim relationship, O2 sensor to fuel trim relation, FT and vacuum leaks, ignition timing and idle control, test conclusion) - Test # 2 (Misfire Detection Strategy, EGR, Ignition and Mechanical misfires) (misfires and OBD2, scanner misfire detection – a time saver, OBD2 40 and 80 cycle misfire, ignition, injector and EGR density misfire, coil-on-plug, misfires and O2 sensor, lean O2 & Secondary misfire, O2 sensor & injector misfires, leaky injector, EGR and the MAP, Type A, B, C misfires, test conclusion) - Test # 3 (Air/Fuel Ratio Faults) (air-fuel imbalance, MAF and post O2 sensors, open-closed-loop, fuel enable, HC & CO relation to AF issues, test conclusion) - Test # 4 (BARO, MAP & MAF PID analysis) (MAP & valve timing faults, ECM behavior, fuel delivery or duty cycle test, volumetric efficiency, , test conclusion) - Test # 5 (Clogged exhaust) (clogged catalytic converter detection, TPS, MAF and converters, idle and WOT or wide open throttle values, vacuum readings, MAP to WOT chats analysis, engine and MAP vacuum, test conclusion) - Test # 6 (EGR Fault Detection) (EGR and MAP values, ECM reaction to EGR issues, EGR temp sensor, DPFE sensor, EGR and O2-MAP and lift position sensor, EGR and engine pre-loading, EGR and the ECM erroneous high LOAD issues, test conclusion) - Test # 7 (O2 Sensor Heater) (O2 heaters and why?, tough to check O2 heater issues, O2 heater effect on signal output, O2 heater bias voltage, engine off and O2 changing value, test conclusion) - Test # 8 (Resetting Fuel Trims) (resetting injection pulse corrections, long-term and short-term fuel trims, learn condition, Lambda, case study on fuel trims, FT resetting according to manufacturer, test conclusion) - Test # 9 (Engine Cranking Vacuum Test) (MAP/MAF cranking vacuum, vacuum to PID analysis, vacuum leaks, gauge-PID test, sources of leaks, cranking values, test conclusion)

Author : Tom Denton
Publisher : Routledge
ISBN 13 : 1317931289
Total Pages : 701 pages
Book Rating : 4.87/5 ( download)

DOWNLOAD NOW!

Download or read book Automobile Electrical and Electronic Systems written by Tom Denton and published by Routledge. This book was released on 2017-09-12 with total page 701 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook will help you learn all the skills you need to pass all Vehicle Electrical and Electronic Systems courses and qualifications. As electrical and electronic systems become increasingly more complex and fundamental to the workings of modern vehicles, understanding these systems is essential for automotive technicians. For students new to the subject, this book will help to develop this knowledge, but will also assist experienced technicians in keeping up with recent technological advances. This new edition includes information on developments in pass-through technology, multiplexing, and engine control systems. In full colour and covering the latest course specifications, this is the guide that no student enrolled on an automotive maintenance and repair course should be without. Designed to make learning easier, this book contains: Photographs, flow charts, quick reference tables, overview descriptions and step-by-step instructions. Case studies to help you put the principles covered into a real-life context. Useful margin features throughout, including definitions, key facts and ‘safety first’ considerations.

Author : Steven X. Ding
Publisher : Springer Science & Business Media
ISBN 13 : 1447164105
Total Pages : 300 pages
Book Rating : 4.04/5 ( download)

DOWNLOAD NOW!

Download or read book Data-driven Design of Fault Diagnosis and Fault-tolerant Control Systems written by Steven X. Ding and published by Springer Science & Business Media. This book was released on 2014-04-12 with total page 300 pages. Available in PDF, EPUB and Kindle. Book excerpt: Data-driven Design of Fault Diagnosis and Fault-tolerant Control Systems presents basic statistical process monitoring, fault diagnosis, and control methods and introduces advanced data-driven schemes for the design of fault diagnosis and fault-tolerant control systems catering to the needs of dynamic industrial processes. With ever increasing demands for reliability, availability and safety in technical processes and assets, process monitoring and fault-tolerance have become important issues surrounding the design of automatic control systems. This text shows the reader how, thanks to the rapid development of information technology, key techniques of data-driven and statistical process monitoring and control can now become widely used in industrial practice to address these issues. To allow for self-contained study and facilitate implementation in real applications, important mathematical and control theoretical knowledge and tools are included in this book. Major schemes are presented in algorithm form and demonstrated on industrial case systems. Data-driven Design of Fault Diagnosis and Fault-tolerant Control Systems will be of interest to process and control engineers, engineering students and researchers with a control engineering background.

Author : Tom Denton
Publisher : Routledge
ISBN 13 : 1317931300
Total Pages : 996 pages
Book Rating : 4.00/5 ( download)

DOWNLOAD NOW!

Download or read book Automobile Mechanical and Electrical Systems written by Tom Denton and published by Routledge. This book was released on 2017-08-25 with total page 996 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of Automobile Mechanical and Electrical Systems concentrates on core technologies to provide the essential information required to understand how different vehicle systems work. It gives a complete overview of the components and workings of a vehicle from the engine through to the chassis and electronics. It also explains the necessary tools and equipment needed in effective car maintenance and repair, and relevant safety procedures are included throughout. Designed to make learning easier, this book contains: Photographs, flow charts and quick reference tables Detailed diagrams and clear descriptions that simplify the more complicated topics and aid revision Useful features throughout, including definitions, key facts and ‘safety first’ considerations. In full colour and with support materials from the author’s website (www.automotive-technology.org), this is the guide no student enrolled on an automotive maintenance and repair course should be without.

Author : Ranjan Ganguli
Publisher : CRC Press
ISBN 13 : 146650272X
Total Pages : 255 pages
Book Rating : 4.27/5 ( download)

DOWNLOAD NOW!

Download or read book Gas Turbine Diagnostics written by Ranjan Ganguli and published by CRC Press. This book was released on 2012-12-13 with total page 255 pages. Available in PDF, EPUB and Kindle. Book excerpt: Widely used for power generation, gas turbine engines are susceptible to faults due to the harsh working environment. Most engine problems are preceded by a sharp change in measurement deviations compared to a baseline engine, but the trend data of these deviations over time are contaminated with noise and non-Gaussian outliers. Gas Turbine Diagnostics: Signal Processing and Fault Isolation presents signal processing algorithms to improve fault diagnosis in gas turbine engines, particularly jet engines. The algorithms focus on removing noise and outliers while keeping the key signal features that may indicate a fault. The book brings together recent methods in data filtering, trend shift detection, and fault isolation, including several novel approaches proposed by the author. Each method is demonstrated through numerical simulations that can be easily performed by the reader. Coverage includes: Filters for gas turbines with slow data availability Hybrid filters for engines equipped with faster data monitoring systems Nonlinear myriad filters for cases where monitoring of transient data can lead to better fault detection Innovative nonlinear filters for data cleaning developed using optimization methods An edge detector based on gradient and Laplacian calculations A process of automating fault isolation using a bank of Kalman filters, fuzzy logic systems, neural networks, and genetic fuzzy systems when an engine model is available An example of vibration-based diagnostics for turbine blades to complement the performance-based methods Using simple examples, the book describes new research tools to more effectively isolate faults in gas turbine engines. These algorithms may also be useful for condition and health monitoring in other systems where sharp changes in measurement data indicate the onset of a fault.